It is the same order a designer follows before a bathroom remodeling estimate. The sizes are the Florida Building Code’s minimums for homes, set beside the roomier planning guidelines of the National Kitchen & Bath Association (NKBA). Work through the steps below and the plan will hold up when a contractor measures it.

Step 1: Measure the room and find the plumbing

Draw the room to scale on graph paper or in a planner app, then measure and mark:

  • Each wall at floor level, and the ceiling height. Measure both diagonals too; if they differ, the room is out of square and new tile will show it.
  • Every door and window: its width, which way the door swings, and the height of each window sill above the floor.
  • The toilet’s rough-in: the distance from the finished back wall to the center of the bolts at its base. It decides which new toilets fit without moving the drain.
  • The center of each drain and water supply, measured from the nearest side wall.
  • Outlets, switches, the exhaust fan, any air conditioning vent and the light fixtures.

Then note what the floor and walls are made of. On a slab, every drain that moves is concrete work; on a framed upper floor, the joists decide where pipes can run. Mark which walls are concrete block, because only a framed wall takes a new pipe or a recessed cabinet without being built out.

Step 2: Check every fixture against the clearances

The Florida Building Code sets the minimum spacing for fixtures in a home. The NKBA guidelines are recommendations, not law, but they describe a comfortable bathroom. Plan to the code everywhere, and to the NKBA figures where the room allows.

Step 2: Check every fixture against the clearances
ClearanceMinimumSet by
Toilet, sink or bidet: its center to a side wall, partition or vanity15 inchesFlorida code
Two fixtures side by side, center to center30 inchesFlorida code
Clear space in front of a toilet, sink or bidet21 inches, to any wall, fixture or doorFlorida code
Shower, inside900 square inches, and 30 inches at its narrowest (or 25 inches with 1,300 square inches)Florida code
Shower entry22 inches clearFlorida code
Exhaust fan50 cfm when switched on, or 20 cfm running continuouslyFlorida code
Outlet distance from a tub or shower edge3 feet horizontally, 8 feet verticallyFlorida code (NEC 406.9(C))
Clear floor space at each fixture30 to 32 inches wide by 48 to 52 inches deepNKBA
Walkway36 inches wideNKBA
Doorway34 inches clear, which takes a 36-inch doorNKBA
Exhaust fan60 cfmNKBA
Outlet distance from a tub or shower edge39 inchesNKBA

Draw each fixture with its clear space in front of it. The NKBA allows those spaces to overlap, but no door should swing through them. Every bathroom outlet also needs ground-fault (GFCI) protection under the National Electrical Code, which Florida adopts through its building code.

Step 3: Choose a layout, starting from the drains

Bathroom layouts are named by how many walls carry fixtures, and each extra wall adds plumbing.

  1. 1. One wall

    Toilet, sink and tub or shower in a row on a single plumbing wall. It is the cheapest to plumb and suits a narrow room.

  2. 2. Two walls

    Fixtures on two walls, often the sink facing the toilet or the shower. It gives more counter and storage, with a second wall of pipes.

  3. 3. Three walls

    The tub or shower across the back, with the toilet and sink on the side walls. A 5-by-8-foot hall bath often works this way, with a 60-inch tub across the 5-foot end.

Keeping every drain where it is keeps the price down. Bathroom remodel cost prices each move, and en suite bathroom renovation explains what a new drain run under a slab involves. Change the layout where it buys something you will use every day, such as a larger shower or a second sink.

Small bathroom layout: where the space comes from

In a small bathroom the floor is the limit, so the gains come from fixtures and doors that take less of it.

  • A pocket door instead of a swinging one. A door that swings in sweeps an arc of floor as wide as the door itself; a pocket door sweeps none. Its wall cavity has to be free of pipes, wires and outlets, a conflict the NKBA guidelines warn about.
  • A wall-hung toilet. The tank goes inside the wall on a carrier, so the bowl sits closer to the wall and the floor beneath it is clear. The wall has to be deep enough for the carrier, which suits a framed wall that is being rebuilt anyway.
  • A floating or shallow vanity, which shows more floor and keeps the walkway clear.
  • A recessed medicine cabinet between the studs, for storage that takes no floor at all.
  • A fixed glass panel or a sliding door on the shower, so no door swings into the room.

Fitting a shower into a small bathroom

The code’s smallest square shower, 30 by 30 inches, is legal but tight, with little room to turn or bend down. A 36-by-36-inch shower has 44% more floor, and a 60-inch-long shower fits the alcove of a standard 60-inch tub. Which one fits depends on the room:

  • A corner shower, square or neo-angle, suits a square room and leaves the walls on either side free.
  • An alcove shower across the end of the room takes the place of a tub without moving any walls.
  • A walk-in shower with a fixed glass panel and no door needs extra length, so the spray stays inside.

Glass near water is a safety item. Florida’s code treats glass in the walls or enclosure of a tub or shower as a hazardous location when its bottom edge is less than 60 inches above the standing surface, so it has to be safety glass. A hinged shower door also swings into the room, so check its arc against the clear space in Step 2. Our shower remodel page covers the curb, the glass and the valve.

Pedestal vs wall-mounted sink

Both take less floor than a vanity, and both give up its storage.

Pedestal vs wall-mounted sink
FeaturePedestal sinkWall-mounted sinkSource
What holds it upA pedestal on the floor, usually with the basin also fixed to the wallThe wall alone, through a bracket or carrier fixed to bracing behind the finish
The pipesPartly hidden behind the pedestalIn view, so many owners choose a decorative trap and supply lines
HeightSet by the pedestalSet at installation, including lower for a seated user
The floor beneathA base to clean aroundClear
Typical installed cost, national$400 to $1,200$400 to $1,6001

A wall-mounted sink needs bracing in the wall to hang safely, which costs little while the wall is open and a great deal once it is tiled.

Of the two, only the wall-mounted sink leaves room for a seated user’s knees. The ADA’s design standards cover public buildings, not private homes, but their sink sizes are a useful reference: a rim no higher than 34 inches above the floor, and clear knee space 30 inches wide reaching 27 inches up beneath it. Our aging-in-place bathroom page covers the rest of an accessible room.

Turning a closet into a bathroom

A closet can become a half bath, with a toilet and sink, or a full bath if it is big enough for a shower as well. Check it against Step 2 first. A toilet alone needs 30 inches of width, plus its own depth and 21 inches in front, so a reach-in closet about 2 feet deep cannot hold one without borrowing floor from the room beside it.

A closet has no window, and that is allowed: Florida’s code waives the bathroom window when there is artificial light and a local exhaust fan. The fan has to discharge outdoors, never into the attic, a soffit or a ridge vent.

The plumbing is the larger question. The new drain has to reach an existing line at the right slope, and where it cannot, an upflush toilet can pump the waste there instead; en suite bathroom renovation covers both. The closet’s storage has to move somewhere too, and our storage solutions work often finds room for it in the same bedroom.

Fixr’s 2026 cost guide puts a closet-to-bathroom conversion at $5,000 to $15,000, and converting existing space into a bathroom at $200 to $250 a square foot, both national ranges. Moving plumbing and adding circuits are permitted work; see remodeling permits.

Online bathroom planners, and what they miss

Two bathroom design tools are free to start: Planner 5D shows a bathroom in 2D and 3D, and RoomSketcher’s free plan includes 2D and 3D floor plans. Draw the room to your measurements and move the fixtures until one layout works.

What they cannot show is what is behind the drywall and under the floor. A planner will let you put a toilet anywhere and run a drain across a slab as if it cost nothing, so treat the drawing as a sketch and check it against the steps here.

When you bring us a sketch, our in-house designers redraw it from measurements taken on site, with the plumbing and framing we find, and can show you the result in 3D.

Step 4: Choose in the right order, then set the budget

Some choices have to be made before the walls close. Pick the shower valve and its trim together, because a trim usually fits only its own maker’s valve, and the valve goes in at rough-in. Settle wall-hung fixtures, bracing for grab bars and the locations of niches at the same stage.

Tile, the vanity and the lighting follow, and frameless shower glass comes last, measured once the tile is on the walls.

Set the budget against real ranges before you fall for a finish. Bathroom remodel cost has them, with bathroom renovation ideas on a budget, and holding part of the budget back covers what the walls hide. When you are ready to compare contractors, how to choose a remodeling contractor lists what to ask.

Questions about planning a bathroom remodel

How does a pedestal sink compare to an undermount sink in a vanity?

An undermount sink is set beneath a countertop on a vanity, so you gain counter space and storage below it, at the cost of floor and depth. A pedestal sink gives that floor back but leaves only a narrow rim for a toothbrush and nothing underneath. In a bathroom of ordinary size the vanity usually earns its space; in a powder room or a very small bath, the pedestal often does.

Are wall-mounted sinks good for small bathrooms?

Often, yes. With nothing on the floor the room reads larger and is quicker to clean, and the sink can sit at whatever height suits you. Plan where the storage it gives up will go, such as a recessed medicine cabinet or shelves above the toilet.

Which way should a bathroom door swing?

In a small bathroom, out into the hall or bedroom, or into a pocket in the wall. A door that swings in has to clear every fixture, and the code measures the clear space in front of the toilet and sink to the door as well as to the walls, so an inward swing can use up floor the room cannot spare.

Can I remodel a bathroom without moving the plumbing?

Yes, and it is the least expensive way to change one. New fixtures on the existing rough-ins, a vanity on the same wall, new tile, lighting and a better fan all leave the drains where they are.

Sources

  1. 1.Fixr, Bathroom Sink Installation cost guide (updated January 30, 2025) (opens in a new tab), checked
  2. 2.Fixr, Bathroom Addition cost guide (updated January 22, 2026) (opens in a new tab), checked
  3. 3.Florida Building Code, Residential, 8th Edition (2023), Chapter 27 Plumbing Fixtures (via UpCodes) (opens in a new tab), checked
  4. 4.Florida Building Code, Residential, 8th Edition (2023), Chapter 15 Exhaust Systems (via UpCodes) (opens in a new tab), checked
  5. 5.National Kitchen & Bath Association, Kitchen & Bath Planning Guidelines, 4th Edition, summary (2022) (opens in a new tab), checked
  6. 6.Florida Building Code, Building, 8th Edition (2023), Section 2701.1, adopting NFPA 70 (2020) (via UpCodes) (opens in a new tab), checked
  7. 7.Florida Building Code, Residential, 8th Edition (2023), Chapter 3 (via UpCodes) (opens in a new tab), checked
  8. 8.ADA National Network, Does the ADA cover private apartments and private homes? (opens in a new tab), checked
  9. 9.U.S. Access Board, 2010 ADA Standards for Accessible Design, Sections 306 and 606 (opens in a new tab), checked
  10. 10.Florida Building Code, Building, 8th Edition (2023), Section 105.1 (via UpCodes) (opens in a new tab), checked
  11. 11.Planner 5D, Bathroom Planner Tool (opens in a new tab), checked
  12. 12.RoomSketcher, Pricing (opens in a new tab), checked